Announcement

Collapse
No announcement yet.

Driveshaft U-joints?

Collapse

Ad Widget

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Driveshaft U-joints?

    What u-joints do stock 4.0/manual/D30/D35 TJ front and rear driveshafts use?
    [COLOR=blue]Chris[/COLOR]
    SAVE JOHNSON VALLEY!!! - CLICK HERE
    Ya Savvy?

    Motech Performance

  • #2
    1310 series... same ones as the XJs and YJs

    Comment


    • #3
      thank you Chuck
      [COLOR=blue]Chris[/COLOR]
      SAVE JOHNSON VALLEY!!! - CLICK HERE
      Ya Savvy?

      Motech Performance

      Comment


      • #4
        my stock u joints on the 6 cylinder yj were 1330 series joints.
        measure the yoke on the rear end.... it is either 3.5" or 3.875"
        >>>>>>>>>>>>>>>>>>>>>>>>>>
        ERIK


        95 yj, locked lifted, and ready to rock!

        Comment


        • #5
          Originally posted by NAILER341
          my stock u joints on the 6 cylinder yj were 1330 series joints.
          measure the yoke on the rear end.... it is either 3.5" or 3.875"
          Hmmm, so is there no set of rules for what U-joints are in there?:confused:
          So its either 1310 or 1330
          I will try to measure the yoke.

          anyone else?
          [COLOR=blue]Chris[/COLOR]
          SAVE JOHNSON VALLEY!!! - CLICK HERE
          Ya Savvy?

          Motech Performance

          Comment


          • #6
            1310 or 1330 won't get you far with the average parts store employee. Trust me I tried. hold on... <goes to jeep to check spares>
            myJeeprocks.com

            "in the end... the rocks always win."

            Comment


            • #7
              ujoint for 1310 series yoke (standard TJ shafts)... 5-153X

              ujoint w/flush fitting in cap for CV... 5-433-1X
              myJeeprocks.com

              "in the end... the rocks always win."

              Comment


              • #8
                http://www.lightruck.com/driveshaft_parts.asp
                >>>>>>>>>>>>>>>>>>>>>>>>>>
                ERIK


                95 yj, locked lifted, and ready to rock!

                Comment


                • #9
                  Two pinion yokes were used on the YJ's D35C rear axle. Through 1993, Spicer part #2-4-6901-1X was utilized. This yoke uses 1310 series U-joints measuring 3 7/32" cap-to-cap. In 1994 and 1995, a larger pinion yoke part #2-4-7631-1 was employed which uses 1330 series U-joints measuring 3 5/8" cap-to-cap.
                  >>>>>>>>>>>>>>>>>>>>>>>>>>
                  ERIK


                  95 yj, locked lifted, and ready to rock!

                  Comment


                  • #10
                    Originally posted by NAILER341
                    http://www.lightruck.com/driveshaft_parts.asp
                    interesting. I don't see my part #s there. :confused:
                    myJeeprocks.com

                    "in the end... the rocks always win."

                    Comment


                    • #11
                      I found the front driveshaft Spicer P/N's.

                      These are interchangeable:
                      5-153X is greasable
                      5-785X is non-greasable

                      I would assume the rear shaft uses the same joints.
                      [COLOR=blue]Chris[/COLOR]
                      SAVE JOHNSON VALLEY!!! - CLICK HERE
                      Ya Savvy?

                      Motech Performance

                      Comment


                      • #12
                        TJ's are definately 1310's front and rear.
                        1994 Toyota, dual cases, 5.29 axles with ARB's

                        Comment

                        Working...
                        X